Grade A Carbon Planchets - Ted Pella, Inc. Alternative Product: Vitreous Carbon Planchets
Pure polished carbon wafers provide a low background signal for spectroscopic
analysis. Suggested for work with fine particulates.
No. 17600: Grade A Carbon Planchets, 1" x 1/16" Polished
Each.
No. 17610: ½" x 1/16" Polished
Each.
No. 17620: 3/8" x 1/16" Polished
Each.
Carbon Planchets - Ted Pella, Inc. Alternative Product: Carbon Planchets
Pure unpolished carbon wafers provide a low background signal for spectroscopic
analysis. Not recommended for fine particulates. Use to minimize background features.
No. 17601: 1" X 1/16" Unpolished - Ted Pella, Inc. Order Code: #16510
Each.
No. 17611: ½" x 1/16" Unpolished - Ted Pella, Inc. Order Code: #16500
Each.
No. 17621: 3/8" x 1/16" Unpolished - Ted Pella, Inc. Order Code: #16504
Each.
No. 17659: Carbon Particle/Powder Mount, 1"dia. - Discontinued
No. 17658: Carbon Particle/Powder Mount, 3/4" dia., each - Discontinued
A pyrolytic graphite disc with a 8mm diameter x 1.5mm deep recess. Use back side as a standard planchet, or the recess for bulk powder samples. Fits No. 17590 Planchet Holder. 3/4" or 1" pyrolytic graphite discs with multiple recesses available on special order, each.
No. 17580: Planchet Holder
For 3/8" and ½" planchets.
No. 17590: Planchet Holder
For 3/4" and 1" planchets. Handy, reusable holders to fit four sizes of planchets. Bases made to fit specific models of microscopes. Specify make and model of SEM.
No. 18906: Pin-Type Mount Holder - Ted Pella, Inc. Alternative Product: #15310-12
Holds up to twelve 1/8" pin-type mounts for sputter coating or sample
preparation. 21/8" dia. x ½" thick aluminum. . . .
.$68.85
Pin-Type Mount Holder With dovetail.
Multi-Mini Mounts - Discontinued
1/8" x ¼" pins set into SEM mount. Useful for viewing a number
of small samples at one time, such as pollen grains, fine particulates,
etc. Pin-type and 10mm stub-type mounts hold 4 Mini-mounts. 15mm and larger
stub-type mounts hold 8.
No. 18814: 4-Pin Mount (Specify
make & model of microscope).
No. 18818: 8-Pin Mount (Specify
make & model of microscope).
No. 18811: Mini-Mount Pins, pkg/16.
Mini-mount pins can be stored in No. 15690
EFFA Mini-Vials.
Silicon Chip Mounts - Ted Pella, Inc. Alternative Product: PELCO SEMclip™ Specimen Mounts
1" diameter x 1" high aluminum mount with angled surface. Surface has
spring clips for holding flat specimens. Ideal for viewing surfaces and
cross sections of the same sample. Eliminates complicated setups or high
tilt angles on the SEM stage. Available with surface angled 45° or
60° from horizontal. Specify make and model of microscope.
No. 18845: 45° Surface Angle Mount.
No. 18860: 60° Surface Angle Mount .
Spring Clip Mount - Ted Pella, Inc. Alternative Product: PELCO SEMclip™ Specimen Mounts
A 1" diameter surface with phosphor bronze clip to hold and ground
the specimen. Ideal for flat specimens. Eliminates silver paint in many
applications. Specify make & model of SEM or Catalog Number of mount
desired.
No. 18801: Mount With 1 Clip.
No. 18802: Mount With 2 Clips.
No. 18803: Mount With 3 Clips.
No. 18806: Spring Clip for Mounts, each. - Ted Pella, Inc. Alternative Product: #16399
No. 18807: Mounting Screws for Spring Clip Mount, pkg/10. - Ted Pella, Inc. Alternative Product: #16399-10
No. 18804: Vertical Spring Clip Mount - Ted Pella, Inc. Order Code: #16143
Holds a sample vertically to study cross sections, coating thicknesses,
etc. Vertical surface is at center of mount. 12.7mm W x 16mm H. Please
specify make & model of SEM.
1/8" Pin Version.
Custom Diameter Stub Version.
No. 18805: Vertical Spring Clip Mount - Ted Pella, Inc. Order Code: #16141
Holds 4 samples vertically to study cross sections, coating thicknesses,
etc. Mount is indexed by rotating SEM stage. 12.7mm square. Available with
pin or stub base. Please specify make & model of SEM.
1/8" Pin Version.
Custom Diameter Stub Version.
No. 18808: EBeam Lithography Holder - Ted Pella, Inc. Order Code: #16405
Spring Clip Mount with Gold Standard and Faraday Cup. Specify make and model of microscope, or
unmounted.
No. 17710: Single Mount Storage Box - Ted Pella, Inc. Alternative Product: #16630
For keeping that one all-important sample in splendid isolation. Avoids
cross contamination of other samples. Holds one 1/8" pin-type mount. Inside measurements 1-1/4" x -1/4" x 1-1/4".
Each box.
No. 17715: Single Mount Box For Hitachi Threaded Mounts - Ted Pella, Inc. Alternative Product: #16630-4
Similar to No. 17710, but with M4 threaded stud to hold Hitachi mounts.
Mount remains in place if box is inverted. Avoids cross contamination of
other samples. Holds one 1/8" threaded mount. Inside measurements 1-1/4" x 1-1/4" x 1-1/4". Each box.
No. 17740: Hitachi Mount Box - Ted Pella, Inc. Alternative Product: #16791
Holds twelve threaded mounts up to 26mm diameter for S-500.
No. 17741: Hitachi Mount Box - Ted Pella, Inc. Alternative Product: #16791
1-1/8" x 4" x 4-3/4" plastic box with Lucite mount tray. Holds twelve 26mm Hitachi mounts, No. 18770 or equivalent.
No. 17742: Hitachi Tray Only.
No. 17743: Hitachi Threaded Mount Box - Ted Pella, Inc. Alternative Product: #16791
Features M4 threaded studs to securely hold Hitachi mounts if the box is inverted. Holds 12 mounts. 1-1/8" x 4" x 4-3/4". Each box.
No. 17755: Sealed Mount Storage Box - Ted Pella, Inc. Alternative Product: #16709
Holds 18 pin-type mounts, each stored in its own vial. Reduces risk of contamination. Sample chart on underside of box lid. Dimensions: 7-3/8"W x 3-11/16"D x 2-3/8"H.
No. 17750: Indexed Storage Tray For Pin-Type Mounts - Ted Pella, Inc. Alternative Product: #16709
Dust-free storage for up to twenty-four 1/8" pin-type mounts. Easy-to-read coding.
No. 17760: Indexed SEM Mount Storage Tray For Stubs - Discontinued
Dust-free storage of up to 24 stub type mounts. Easy-to-read coding. For stubs no larger than 15mm. 4-1/4" x 6" x 1" H.
No. 17770: Plastic Box And Holder For Cambridge S4 Mounts - Discontinued
Holds ten No. 18460 mounts. 5-1⁄2" x 1-7/8" x 1-5/8". Each box.
No. 17800: Plastic Box And Holder For 1/8" Pin-Type Mounts - Ted Pella, Inc. Order Code: #99-17800 (pkg/10) or 16120
Holds four No. 18420 or 18440 mounts. 3" x 1-1⁄4" x 7/8".
No. 17790: Plastic Box And Holder For 1⁄4" Pin-Type Mounts - Discontinued
Holds four No. 18400 mounts.
Alphabetical Product Index
Ernest F. Fullam, Inc. Home Page
